RCD Selection: Why Type AC is Now Restricted Under Regulation 531.3.3

The traditional Type AC Residual Current Device (RCD), sensitive only to pure sinusoidal alternating currents, is no longer fit for modern electrical installations. Everyday equipment including EV chargers, heat pumps, variable speed washing machines, PC power supplies, and LED drivers produce rectified and high-frequency DC residual leakage currents. When smooth DC leakage exceeds 6 mA, Type AC toroids become magnetically blinded. Here is the authoritative engineering breakdown of Regulation 531.3.3, toroid saturation physics, waveform classifications, and cascade selectivity rules under BS 7671.

CLASSIFICATIONStatutory compliance guide
STATUTORY AUTHORITYEAWR 1989 REGS 4(1), 4(3), 8, 16
TECHNICAL STANDARDSBS 7671:2018+A4:2026 REG 531.3.3 // BS EN 62423
ENGINEERING AUDIT28 October 2026 : ADRIAN KING
STATUTORY SELECTION MANDATE & REGULATION 531.3.3

Under BS 7671:2018+A4:2026 Regulation 531.3.3, Type AC Residual Current Devices (RCDs) are restricted to circuits where it is known that the load contains no DC components.In modern UK installations, almost all circuits supply equipment with internal rectification.Fitting or leaving Type AC devices on electronic loads creates a severe latent safety failure: smooth DC residual current saturates the magnetic toroid core, blinding the device and preventing it from tripping during a fatal AC shock, in direct breach of EAWR 1989 Regulation 4(1) and Regulation 8.

CRIMINAL STATUTE & FAULT PROTECTIONEAWR 1989 REGS 4(1), 4(3), 8 & 16 // BS 7671 REG 531.3.3
PRODUCT STANDARDS & SELECTIVITY:BS EN 61008 // BS EN 61009 // BS EN 62423 // REG 536.4.1.4Jump to Statutory Duty Matrix ↓
10-SECOND SELECTION SUMMARY (REGULATION 531.3.3)
01
Type AC Strictly Restricted

Permitted only on circuits serving purely resistive loads with zero electronic controls. Prohibited on general socket outlets and modern appliances.

02
The 6 mA DC Blinding Threshold

Smooth DC leakage exceeding 6 mA saturates the magnetic toroid core, collapsing permeability and preventing the device from tripping on AC shock.

03
Type A is the UK Standard Baseline

Mandatory minimum for general circuits. Reliably detects AC and pulsating DC residual currents with smooth DC components up to 6 mA.

04
Cascade Selectivity (Reg 536.4.1.4)

Never install Type B downstream of Type A or Type AC. Downstream smooth DC will blind the upstream device, disabling whole-board protection.

MAGNETIC PHYSICS // B-H CURVE

Toroid Core Saturation: The Physics of DC Blinding

An RCD operates on the principle of magnetic summation. The line and neutral conductors pass through a high-permeability magnetic core (current transformer toroid). Under healthy conditions, the currents in line and neutral are equal and opposite, producing zero net magnetic flux in the core:

HEALTHY AC OPERATION
Φ_net = 0

Line and neutral currents cancel. Zero magnetic flux in the toroid. Secondary detection coil voltage remains zero.

AC EARTH FAULT
e = -N (dΦ/dt)

Unbalanced current generates alternating flux. Secondary coil produces EMF, energising the polarized relay to trip the mechanism.

DC BLINDING STATE
ΔB / ΔH → 0

Smooth DC leakage ≥ 6 mA drives core into magnetic saturation (Bsat). Permeability collapses; zero EMF induced during AC faults.

DANGER: THE FATAL ILLUSION OF SAFETY UNDER DC CORE BLINDING

DC blinding is completely invisible during routine mechanical trip tests using the integral test button. The test button passes pure AC current through an internal loop, which may mechanically trip an un-blinded device. However, when an electronic load (such as a variable speed heat pump or EV charger) leaks smooth DC onto the protective conductor, the toroid saturates instantly. If a person subsequently touches an exposed live conductor on that circuit, the resulting 230 V AC shock current cannot generate alternating flux in the saturated core. The RCD remains completely frozen, allowing fatal touch voltages to persist indefinitely.

↑ Back to navigation rail
VECTOR ARCHITECTURE // FIGURE 1

RCD Toroidal Core DC Saturation & Statutory Selection Hierarchy

The following technical drawing illustrates how DC residual leakage currents shift toroid cores into magnetic saturation, the four residual current waveform categories defined in BS EN 62423, and the statutory selection hierarchy mandated by BS 7671 Regulation 531.3.3.

BS 7671 REGULATION 531.3.3 // RCD TOROIDAL CORE DC SATURATION & SELECTIONBS EN 62423 // 6mA DC THRESHOLD // EAWR REG 81. TOROID SATURATION PHYSICSThe DC blinding mechanism on Type AC coresCURRENT TRANSFORMER TOROID (SUMMATION)LNPETRIP ACTUATORe = -N (dΦ/dt)B-H CURVE: COLLAPSE OF PERMEABILITYDC residual leakage ≥ 6mA biases the magneticcore beyond the knee into saturation (Bsat).Differential permeability collapses (ΔB/ΔH → 0),preventing secondary voltage generation.FATAL BLINDING DANGERA saturated Type AC toroid will not trip evenif a person receives a 230V AC shock to earth.2. RESIDUAL WAVEFORMSEquipment loads and leakage characteristicsTYPE AC // PURE SINUSOIDAL AC (50Hz)Resistive heating, tungstenStrictly zero electronicsTYPE A // PULSATING RECTIFIED DC (≤ 6mA DC)PCs, switch-mode power,LED drivers, induction hobsTYPE F // COMPOSITE FREQUENCY (≤ 10mA DC)1-phase frequency drives,inverter heat pumps, washingTYPE B // SMOOTH PURE DC & 3-PHASE RECTIFIEDEV chargers, solar battery,3-phase inverters, UPSStandard detection frequency range: 0Hz to 100kHz3. STATUTORY SELECTIONReg 531.3.3 hierarchy and cascade selectivityRCD SELECTION STATUS UNDER BS 7671Type AC:RESTRICTED (NOTE 1)Prohibited where loads contain electronics.Type A:GENERAL BASELINEStandard domestic and commercial circuits.Type F:INVERTER SPECIFICSingle-phase variable speed heat pumps.Type B / EV:SMOOTH DC / RDC-DDEV chargers (BS IEC 62955), 3-phase PV.REGULATION 536.4.1.4 CASCADE RULEBANNED: Type B downstream of Type A / ACIf a downstream device passes smooth DCfault currents, it will blind any upstreamType A or Type AC RCD, disabling whole-boardprotection. Upstream must be Type B or Type S.BS 7671:2018+A4:2026 §531.3.3 // BS EN 61008-1 // BS EN 61009-1 // BS EN 62423CRITICAL CRITERION: 6mA SMOOTH DC BLINDS TYPE AC TOROIDS // VERIFIED OCT 2026
Figure 1: RCD Toroidal Core DC Saturation Physics and Statutory Selection Hierarchy.Illustrating how DC residual leakage currents shift toroid cores into magnetic saturation ("blinding"), the four residual current waveform categories under BS EN 62423, and mandatory cascade selectivity rules under BS 7671 Regulation 536.4.1.4.
↑ Back to navigation rail
PRODUCT STANDARDS // RESIDUAL WAVEFORMS

Residual Current Waveform Classifications Under BS EN 62423

Electrical loads generate distinct fault signatures depending on their internal power conversion circuitry. BS EN 62423 and BS 7671 classify protective devices into four progressive categories:

TYPE AC (RESTRICTED)
50 Hz Pure Sine

Responds only to sinusoidal alternating currents. Blinds when smooth DC residual leakage exceeds 6 mA. Restricted under Regulation 531.3.3 Note 1.

TYPE A (UK BASELINE)
Pulsating DC + AC

Detects sinusoidal AC and pulsating rectified DC currents up to 6 mA smooth DC. Standard specification for domestic socket circuits.

TYPE F (FREQUENCY DRIVES)
Up to 1 kHz + 10 mA DC

Detects Type A waveforms plus composite high frequencies up to 1 kHz and smooth DC up to 10 mA. Tailored for single-phase inverter heat pumps.

CAUTION: TYPE B REQUIREMENTS FOR THREE-PHASE INVERTERS & SOLAR STORAGE

Type B RCDs incorporate dual magnetic sensing cores: a standard flux toroid for high-frequency and AC detection, combined with an active Hall-effect sensor or fluxgate oscillator to detect smooth pure DC currents up to 100 kHz. Any three-phase variable speed drive, commercial solar inverter without galvanic isolation, or battery storage energy system capable of generating smooth DC residual current requires a Type B device under BS 7671 Regulation 531.3.3.

↑ Back to navigation rail
SPECIFICATION GUIDE // MASTER TABLE

Master Equipment Selection Matrix (BS 7671 Regulation 531.3.3)

The following table establishes the required RCD type for common domestic, commercial, and industrial loads:

Circuit / Connected LoadExpected Residual WaveformPermitted Minimum RCD TypeDC Fault ToleranceProhibited Types
General Socket Outlets (13 A BS 1363)Pulsating DC, switch-mode harmonicsType ASmooth DC ≤ 6 mAType AC
Domestic Heat Pumps (1-Phase Inverter)Composite high frequency, pulsating DCType F or Type A*Smooth DC ≤ 10 mA (Type F)Type AC
Electric Vehicle Chargers (Mode 3)Smooth DC from vehicle battery rectifierType A + 6 mA RDC-DD (or Type B)Pure DC detection at 6 mAType AC, Type A alone
Solar PV Inverters (Transformerless)Smooth DC from DC string busbarsType B (unless isolated per 712.411.3.2.1)Smooth DC up to 100 kHzType AC, Type A
Commercial 3-Phase Variable Speed Drives3-phase bridge rectified smooth DCType BContinuous smooth DCType AC, Type A, Type F
Direct Electric Immersion Heater (Fixed)Pure 50 Hz sinusoidal alternating currentType AC permitted (Type A preferred)Zero DC component expectedNone (subject to load audit)
LED Commercial Lighting CircuitsHigh harmonic pulsating DC from driversType ASmooth DC ≤ 6 mAType AC
BENCH NOTE: HEAT PUMP MANUFACTURER INSTRUCTIONS (REGULATION 510.3)

*BS 7671 Regulation 510.3 requires electrical equipment to be installed in accordance with manufacturer instructions. Many heat pump manufacturers explicitly specify Type F or Type B RCDs in their installation manuals. Fitting a standard Type A device where the manufacturer mandates Type F renders the installation non-compliant and invalidates manufacturer warranties.

↑ Back to navigation rail
SELECTIVITY ARCHITECTURE // REGULATION 536.4.1.4

Upstream Cascade Selectivity & DC Blinding Prevention

In installations where multiple RCDs are connected in series (for example, a front-end 100 mA or 300 mA time-delayed device protecting sub-mains, followed by 30 mA branch devices), engineers must account for DC fault propagation.

CASCADE SELECTIVITY RULES UNDER BS 7671 REGULATION 536.4.1.4BS 7671:2018+A4:2026 §536.4.1.4
Rule 1
RCD Type Compatibility in Series:

An upstream RCD must have equal or higher DC tolerance than any downstream device:

  • Permitted Cascade: Upstream Type B → Downstream Type B, Type F, Type A, or Type AC.
  • Permitted Cascade: Upstream Type F → Downstream Type F, Type A, or Type AC.
  • Permitted Cascade: Upstream Type A → Downstream Type A or Type AC.
  • STRICTLY PROHIBITED: Upstream Type A or Type AC with downstream Type B or Type F.
Rule 2
Time-Delay Discrimination (Type S):

To achieve discrimination, the upstream device must be a Type S (selective / time-delayed) unit with a rated residual current at least 3 times the downstream device (for example, 100 mA Type S upstream of 30 mA instantaneous).

Rule 3
Standing Earth Leakage Limit (Regulation 531.3.2):

I_leak(standing) ≤ 0.3 × I_Δn = 0.3 × 30 mA = 9 mA

Accumulated protective conductor currents from filter capacitors must not exceed 9 mA on a 30 mA circuit to prevent premature tripping and pre-magnetisation of the toroid.

↑ Back to navigation rail
TECHNICAL WISDOM // APPRENTICE EXPLAINERS

Deep Bench Notes: Practical Testing & Commissioning

Bench Note 1: Why the Integral Test Button Does Not Verify DC Protection

The test button on an RCD connects a resistor between line on one side of the toroid and neutral on the other side. This creates an artificial 50 Hz AC leakage current across the core. It proves that the internal sense coil, electronic amplifier, trip relay, and mechanical spring mechanism are operational. However, it proves nothing about the device's ability to resist DC saturation blinding. Only testing with an instrument capable of generating pulsating DC (Type A test) or smooth DC ramps (Type B test) proves the device meets its designated standard.

Bench Note 2: Mode 3 EV Charging & BS IEC 62955 RDC-DD Operation

BS 7671 Regulation 722.411.4.1 mandates that EV charge points must have protection against DC earth leakage. Electric vehicles have high-capacity on-board AC-to-DC rectifiers. If insulation breaks down between the DC bus and the vehicle chassis, smooth DC leakage flows back through the charging cable. To protect upstream domestic Type A RCDs from being blinded by this DC leakage, the charge point must either:

  • Incorporate a Residual Direct Current Detecting Device (RDC-DD) conforming to BS IEC 62955, which automatically disconnects the vehicle when smooth DC leakage reaches 6 mA, allowing the upstream Type A RCD to continue operating safely.
  • Be protected directly by a dedicated Type B RCD, which is immune to DC saturation up to its full rated capacity.
Bench Note 3: Periodic EICR Coding for Existing Type AC RCDs

When conducting a periodic inspection (EICR) on an older installation fitted with Type AC RCDs:

  • Code C3 (Improvement Recommended): Standard domestic circuits where equipment was compliant at the time of installation and shows no specific evidence of equipment requiring Type A or Type F protection (Electrical Safety First Best Practice Guide 4 Item 3.12).
  • Code C2 (Potentially Dangerous): Where a Type AC RCD supplies dedicated circuits serving equipment known to produce smooth DC residual currents, such as an EV charger, solar PV battery storage, or heat pump with manufacturer instructions requiring Type A, Type F, or Type B.
Bench Note 4: RCD Testing Requirements Under Regulation 643.7

BS 7671:2018+A4:2026 Regulation 643.7 simplifies RCD testing requirements. The historical requirement to test at 0.5 × IΔn and 5 × IΔn for standard installation sign-off has been streamlined:

  • Verification of Disconnection: The primary test is verification that the RCD operates within maximum permitted disconnection times at 1 × IΔn (300 ms for general type, 130 ms to 500 ms for Type S).
  • Phase Angle: Test at both 0° and 180° phase angles, recording the longest tripping time on the schedule of test results.
  • Integral Test Button: The mechanical test button must be operated to verify mechanical free movement of the switch mechanism.
↑ Back to navigation rail
LEGAL COMPLIANCE // EAWR 1989

Statutory Duty Matrix: RCD Protection & Criminal Liabilities

Specifying and maintaining appropriate RCD protection is essential to discharge statutory safety duties under the Electricity at Work Regulations 1989.

RegulationStatutory DutyDuty NatureEngineering Mandate & Defense
Reg 4(1)All systems shall at all times be constructed and maintained to prevent danger.Qualified (SFARP)Ensure RCDs remain responsive to expected load residual currents and are not blinded by DC core saturation.
Reg 4(3)Work on or near electrical systems shall not give rise to danger.Qualified (SFARP)Verify RCD type selection during additions or alterations and test tripping times using calibrated multi-function testers.
Reg 8Earthing or other suitable precautions against electric shock.AbsoluteWhere additional protection or fault protection relies on RCDs, devices must operate within mandatory disconnection times.
Reg 16Competence to prevent danger and injury.AbsoluteEngineers must understand Regulation 531.3.3 and manufacturer equipment instructions when specifying protective devices.
Reg 29Statutory defence in criminal proceedings.DefenseProof that all reasonable steps were taken and due diligence exercised. Documented equipment selection matrices and trip test logs provide this evidence.
↑ Back to navigation rail

Frequently Asked Questions

Can I ever install a Type AC RCD in a new installation?
Under BS 7671:2018+A4:2026 Regulation 531.3.3 Note 1, Type AC RCDs may only serve fixed equipment where it is known that the load contains no DC components. Because almost all modern appliances and luminaires contain rectifiers or power electronics, Type AC RCDs are practically obsolete for new general installations and should not be specified.
What happens if a Type B RCD is installed downstream of a Type A RCD?
If a fault occurs downstream generating smooth DC leakage (e.g. 10 mA DC), the downstream Type B RCD may tolerate it or clear it. However, before clearance, that smooth DC current flows back through the upstream Type A RCD. The upstream Type A toroid becomes magnetically saturated (blinded), preventing it from tripping during any simultaneous AC fault on other circuits. This violates Regulation 536.4.1.4.
Is a 6 mA DC RDC-DD identical to a Type B RCD?
No. An RDC-DD (Residual Direct Current Detecting Device per BS IEC 62955) is designed specifically to detect smooth DC leakage ≥ 6 mA and open its contacts to protect an upstream Type A RCD from blinding. It does not replace the Type A RCD, which provides the primary 30 mA AC shock protection. A Type B RCD combines both functions in a single unified unit.
Sparks Switchboard
Quick: