GUIDE // SAFETY & COMPLIANCEHASAWA 1974 §2/§3 // SI 1989/635 CURRENT STATUTE HSR25 3RD EDREVISED 30 OCT 2026

EAWR 1989: Electricity at Work Regulations Core Duties & Regulation 14

The Electricity at Work Regulations 1989 (SI 1989/635), made under the Health and Safety at Work etc. Act 1974, constitute the non-negotiable statutory criminal baseline for all UK electrical engineering. Unlike BS 7671 (a non-statutory British Standard code of practice), non-compliance with EAWR is a direct criminal offence carrying unlimited fines and individual custodial liability.

Statutory Compliance Reference: This engineering manual supports dutyholder compliance audits, site safety briefings, and legal risk evaluations. While BS 7671 provides an approved method for meeting EAWR requirements in low-voltage installations, EAWR compliance carries statutory criminal force across every commercial, industrial, and temporary electrical system.
STATUTORY FRAMEWORKEAWR 1989 REGS 1-16 & 29 // HASAWA 1974 §2, §3, §7 // HSR25
Statutory Duty Matrix & Defences ↓
EXECUTIVE STATUTORY SUMMARYSI 1989/635 / HSR25 3RD ED

Enforced strictly by the Health and Safety Executive (HSE), the Electricity at Work Regulations 1989 govern all workplace electrical systems from 24V DC control circuits to 400kV transmission switchgear.

01
Absolute Duties: Regulations 4(1), 4(3), 5, 8, 9, 10, 11, 12, 13, 14, 15, and 16 carry strict criminal liability. Commercial expense or operational inconvenience cannot be cited as a defence.
02
Qualified Duties (SFIRP): Regulations 4(2), 6, and 7 are qualified by "so far as is reasonably practicable". Dutyholders must compute risk quantum against sacrifice per Edwards v NCB [1949].
03
Regulation 14 Three-Condition Gate: Working live is strictly unlawful unless dead working is unreasonable, live working is reasonable, and suitable precautions (GS38, PPE, barriers) are proven.
04
Regulation 29 Defence: The burden of proof is reversed onto the accused dutyholder, who must prove they took all reasonable steps and exercised all due diligence to avoid the offence.
↑ Back to navigation
FIGURE 1: STATUTORY SCHEMATIC

Statutory Hierarchy, Live Work Gateway & Regulation 29 Defence

The following vector schematic outlines the core legal mechanisms of SI 1989/635: the sharp demarcation between Absolute and Qualified duties, the sequential gateway test governing Regulation 14, and the reversal of proof under Regulation 29.

EAWR 1989 // STATUTORY CRIMINAL FRAMEWORK & REGULATION 14 GATEHASAWA 1974 §2/§3 // SI 1989/635 // ABSOLUTE VS QUALIFIED DUTIES // REG 29 DEFENCEPANEL 1: STATUTORY DUTY HIERARCHYCriminal liability standards under SI 1989/635ABSOLUTE DUTIES (NON-QUALIFIED)MUST BE COMPLIED WITH REGARDLESS OF COST• Regs 4(1), 4(3): Systems construction & work safety• Regs 5, 8, 9, 10: Strength, earthing, references• Reg 12: Isolation & disconnection of power• Reg 13: Work on dead equipment (made safe)• Reg 14 & 16: Live work rules & competenceQUALIFIED DUTIES (SFIRP)SO FAR AS IS REASONABLY PRACTICABLE• Reg 4(2): Maintenance of electrical systems• Reg 6: Adverse or hazardous environments• Reg 7: Insulation & conductor protection• Edwards v NCB balance: Risk vs sacrifice calculationREGULATION 29 STATUTORY DEFENCE• Reversal of proof: Defendant must prove innocence• Required test: Took all reasonable steps• Required proof: Exercised all due diligence• Defence excluded for absolute criminal dutiesPANEL 2: REG 14 THREE-CONDITION GATEAll three criteria must be satisfied concurrentlyCONDITION 1 // REGULATION 14(A)Unreasonable in all circumstances for it to be dead• Diagnostic testing, tracing, monitoring (Permitted)CONDITION 2 // REGULATION 14(B)Reasonable in all circumstances to work live• Economic inconvenience or commercial delay is NOT an excuseCONDITION 3 // REGULATION 14(C)Suitable precautions taken to prevent injury• GS38 test probes with ≤ 4mm exposed tips• Arc-rated face shield, insulated tools, barrier sheeting• Accompanied by CPR/first aid competent colleagueCONSEQUENCE OF GATE FAILUREANY CONDITION UNMET = WORK IS ILLEGALDutyholder commits direct criminal offence under HASAWA 1974.Strict liability applies; zero commercial defence.PANEL 3: COMPETENCY & ISOLATIONReg 16 Competency & Reg 12/13 Safe IsolationREGULATION 16: COMPETENCE• Technical knowledge or experience required• Or adequate supervision appropriate to the risk• Apprentices must not work alone on live gear• Absolute duty: Employer liable for incompetent staffREGULATION 12: ISOLATION• Secure disconnection from every power source• Physical air-gap or certified contact separation• Software e-stop is NOT electrical isolationREGULATION 13: PRECAUTIONS• Prevent dead equipment becoming live while working• Padlock off at physical isolator, retain unique key• Prove dead with GS38 indicator before touchingHSE ENFORCEMENT NOTICES• Improvement Notice (Section 21 HASAWA)• Prohibition Notice (Section 22 HASAWA - immediate)• Unlimited corporate fines & custodial sentencesSI 1989/635 • HSE HSR25 3RD EDITION • HASAWA 1974 §2, §3, §7 • EDWARDS V NATIONAL COAL BOARD [1949]Statutory reference
Figure 1: Electricity at Work Regulations 1989 Statutory Duty Structure. Illustrating the legal divide between Absolute and Qualified duties, the mandatory three-condition gateway under Regulation 14 for live work, and the strict limits of the Regulation 29 statutory defence.
↑ Back to navigation
LEGAL ARCHITECTURE

Statutory Duty Structure: Absolute vs SFAIRP

Under HSE guidance document HSR25 (Memorandum of Guidance on the Electricity at Work Regulations 1989), statutory duties are divided into two distinct legal classes:

Duty ClassApplicable RegulationsLegal Definition & Statutory Burden
Qualified (SFIRP)Regulation 4(2), 6, 7Qualified by "so far as is reasonably practicable". The dutyholder must weigh the risk against the sacrifice (money, time, physical trouble) required to avert it. Where the danger involves fatal electric shock or arc flash blast, the sacrifice required to justify inaction is immense.
Absolute DutiesRegulation 4(1), 4(3), 5, 8, 9, 10, 11, 12, 13, 14, 15, 16Must be complied with without regard to cost, difficulty, or project delivery deadlines. In criminal proceedings, a defendant can only rely on the statutory Regulation 29 defence by proving that they took all reasonable steps and exercised all due diligence.
↑ Back to navigation
REGULATION 14 ANALYSIS

The Regulation 14 Live Working Three-Part Gateway

Regulation 14 is one of the most litigated and strictly interpreted safety laws in the UK. It establishes a universal statutory presumption: all electrical work must be performed with equipment dead and securely isolated. Working live is an exceptional departure permitted only when three statutory conditions are satisfied concurrently:

GATE 1 // REGULATION 14(A)Unreasonable to be Dead

It is unreasonable in all circumstances for the conductor to be dead. This condition is satisfied for essential diagnostic tasks such as fault finding, voltage measurements, current clamping, or phase sequencing. It is never satisfied by commercial disruption, the cost of an out-of-hours shutdown, or the unwillingness of a client to power down a server room or factory line.

GATE 2 // REGULATION 14(B)Reasonable in all Circumstances to Work Live

It is reasonable in all circumstances for the operative to be at work on or near it while it is live. The dutyholder must assess whether the operative can maintain safe clearance distances, whether the physical environment is cramped or wet, and whether the task can be safely executed by a human being without uncontrolled contact.

GATE 3 // REGULATION 14(C)Suitable Precautions Taken to Prevent Injury

Suitable precautions (including where necessary the provision of suitable protective equipment) must be taken to prevent injury. This mandates calibrated HSE GS38 two-pole detectors (probes with ≤ 4mm exposed tips), arc-rated face shields, insulated tools certified to BS EN 60900 (1000V rated), insulating safety mats, temporary shroud barriers, and competent accompaniment by a second operative trained in emergency CPR.

↑ Back to navigation
STATUTORY REFERENCE SCHEDULE

The Complete EAWR 1989 Schedule (Regulations 1 to 16)

The complete technical breakdown of Regulations 1 through 16 under statutory instrument SI 1989/635, cross-referenced to UK engineering standards and practical switchroom applications:

RegTitle & Statutory ScopeDuty NaturePractical Engineering Requirement
Reg 1Citation and CommencementN/ACame into force across Great Britain on 1 April 1990. Covers all commercial, industrial, and agricultural workplaces.
Reg 2InterpretationN/ADefines critical statutory terms: electrical system, conductor, danger (risk of injury), and injury (death, shock, burn, arcing, or explosion).
Reg 3Duties of PersonsAbsoluteImposes duties on employers, self-employed contractors, and employees. Employees must cooperate with employers under HASAWA Section 7.
Reg 4(1)Systems ConstructionAbsoluteAll systems shall at all times be of such construction as to prevent, so far as is reasonably practicable, danger.
Reg 4(2)Systems MaintenanceSFIRPAs may be necessary to prevent danger, all systems shall be maintained so as to prevent danger. Mandates planned preventive inspection and testing (EICRs, PAT).
Reg 4(3)Work ActivitiesAbsoluteEvery work activity, including operation, use, and maintenance of electrical systems, shall be carried out in such a manner as not to give rise to danger.
Reg 4(4)Protective EquipmentAbsoluteAny equipment provided for protecting persons at work on or near electrical equipment shall be suitable for use, maintained, and properly used (PPE, GS38 leads).
Reg 5Strength and CapabilityAbsoluteNo electrical equipment shall be put into use where its strength and capability may be exceeded. Mandates prospective fault current (PFC) rating compliance.
Reg 6Adverse EnvironmentsSFIRPElectrical equipment exposed to mechanical damage, moisture, corrosion, dust, or explosive atmospheres must be constructed or protected to prevent danger (IP ratings, ATEX/DSEAR).
Reg 7Insulation & EnclosureSFIRPAll conductors which may give rise to danger must be suitably insulated and protected, or placed in such a position as to prevent danger (basic protection, enclosures).
Reg 8Earthing & PrecautionsAbsolutePrecautions shall be taken, either by earthing or by other suitable means, to prevent danger arising when a conductor becomes charged (fault protection, ADS, bonding).
Reg 9Circuit IntegrityAbsoluteWhere necessary to prevent danger, no conductor shall be broken or have its earth connection removed while energized (integrity of protective conductors).
Reg 10ConnectionsAbsoluteEvery joint and connection in a system shall be mechanically and electrically suitable for use. Prevents high-resistance loose connections and thermal fires.
Reg 11Excess Current ProtectionAbsoluteEfficient means, suitably located, shall be provided for protecting from excess of current every part of a system (circuit breakers, fuses, thermal overloads).
Reg 12Cutting off Supply & IsolationAbsoluteWhere necessary to prevent danger, suitable means shall be available for cutting off the supply and for isolating electrical equipment. Requires physical air-gap isolation.
Reg 13Equipment Made DeadAbsoluteAdequate precautions shall be taken to prevent electrical equipment, which has been made dead, from becoming electrically charged while work is carried out (lock-off, prove dead).
Reg 14Work on Live ConductorsAbsoluteNo person shall engage in work on or near live conductors unless the three-part gateway test is fully satisfied.
Reg 15Working Space & LightingAbsoluteAdequate working space, adequate means of access, and adequate lighting shall be provided at all electrical equipment on which work is carried out.
Reg 16CompetenceAbsoluteNo person shall be engaged in any work activity where technical knowledge or experience is necessary to prevent danger, unless possessing such knowledge or under adequate supervision.
↑ Back to navigation
SENIOR BENCH NOTES

Senior Engineer Operational & Legal Guidance

Bench Note: Why Edwards v National Coal Board [1949] Governs SFAIRP

In the landmark Court of Appeal case Edwards v National Coal Board [1949] 1 KB 704, Lord Justice Asquith established the universal legal definition of "reasonably practicable". The computation requires weighing the risk against the sacrifice (whether in money, time, or trouble). Crucially, the risk must be judged in advance, and the sacrifice must be grosly disproportionate to the risk to justify non-compliance. For electrical danger involving 230V/400V where death or severe maiming is foreseeable, the courts require extraordinary justification before accepting that safety measures were not reasonably practicable.

Bench Note: Why Commercial Delay Never Satisfies the Regulation 14 Test

Electrical dutyholders frequently face pressure from facility managers to replace switchgear components or re-terminate cables while panels remain live, citing that powering down would halt a data centre or food processing line. HSE inspectors and judges have repeatedly confirmed that economic inconvenience, project liquidated damages, or client resistance to a weekend shutdown never make it "unreasonable" to make conductors dead under Regulation 14(a). Live work is strictly reserved for diagnostic actions where physical voltage is required for test measurement.

Bench Note: The Legal Myth of "Permits to Work Sanctioning Live Working"

A common misconception in commercial maintenance is that signing an internal "Live Working Permit" indemnifies the operative or employer. A permit to work is an administrative document; it does not grant legal immunity from the absolute duties of EAWR 1989. If an incident occurs and the investigation reveals that the work could have been carried out dead, the permit serves merely as signed documentary evidence that the employer knowingly authorized unlawful live work.

Bench Note: Domestic Homes as Workplaces Under Section 3 HASAWA 1974

Domestic homeowners are not employers under EAWR, leading some electricians to believe EAWR does not apply in residential properties. This is incorrect. The moment an electrical contractor or sole trader crosses the threshold of a domestic residence to perform work, the premises become a place of work under Section 3 of the Health and Safety at Work etc. Act 1974 and EAWR Regulation 3. The contractor owes statutory duties to themselves, their apprentices, and the building occupants. Safe isolation and GS38 compliance are legally mandatory in domestic switchboards.

↑ Back to navigation
LEGAL COMPLIANCE MATRIX

Statutory Duty & Regulation 29 Defence Matrix

Summary mapping of key EAWR regulations, their duty classification, the enforcement standard under HSR25, and the applicability of the statutory due diligence defence:

RegulationDuty ClassificationEnforcement BenchmarkReg 29 Defence Applicability
Reg 4(1): ConstructionAbsoluteBS 7671 design compliance, component manufacturer approvals.Available: Must prove all reasonable steps taken in specification & verification.
Reg 4(2): MaintenanceQualified (SFIRP)EICR inspection intervals, documented maintenance records, PAT records.Edwards v NCB cost-benefit balance: Burden on dutyholder to prove gross disproportion.
Reg 12: IsolationAbsolutePhysical lock-off, padlocks, air-break contactors. Software lockout excluded.Available: Must prove strict adherence to written lock-out/tag-out procedures.
Reg 13: Made SafeAbsoluteThree-point proving with HSE GS38 detector and dedicated proving unit.Available: Must prove calibrated instruments provided and operative trained/audited.
Reg 14: Live WorkingAbsoluteConcurrent satisfaction of 14(a), 14(b), and 14(c). Zero commercial excuse.Excluded in practice if dead isolation was physically possible.
Reg 16: CompetenceAbsoluteFormal qualifications (NVQ Level 3, AM2, ECS Gold Card), technical supervision.Available: Must prove verified qualification checks and task-specific risk briefings.
↑ Back to navigation
Sparks Switchboard
Quick: