UK DESIGNATED STANDARDS REGISTER

Designated Standards & Statutory Enactments

Structured 3-tier taxonomy categorising UK statutory legislation (mandatory by criminal law), designated engineering codes (presumed conformity), and HSE life safety guidance.

TIER 1 // UK STATUTORY LAW (MANDATORY)STATUTE

Primary Safety & Legal Enactments

Statutory legislation made by Acts of Parliament or Statutory Instruments. Non-compliance carries criminal liability, unlimited fines, and custodial sentences.

Electricity at Work Regulations 1989 (EAWR)

S.I. 1989/635

Imposes strict legal duties on employers, duty holders, and employees. Absolute duties require compliance regardless of cost.

Key Statutory & Technical Requirements:
  • Reg 4: Systems, work activities and protective equipment to be safe at all times.
  • Reg 12: Means for cutting off supply and for isolation of electrical equipment.
  • Reg 13: Adequate precautions for work on equipment made dead (safe isolation).
  • Reg 14: Work on or near live conductors strictly prohibited unless three statutory conditions are simultaneously met.
  • Reg 16: Persons must be competent to prevent danger and injury.

Provision and Use of Work Equipment Regulations 1998 (PUWER)

S.I. 1998/2306

Mandates that all electrical machinery and apparatus used at work is suitable, safe, regularly inspected, and fitted with appropriate control systems.

Key Statutory & Technical Requirements:
  • Reg 5: Maintenance of equipment in an efficient state and working order.
  • Reg 6: Inspection of work equipment by competent persons.
  • Reg 15: Readily accessible control systems and emergency stops.
  • Reg 22: Prevention of spontaneous restart following power restoration.

Dangerous Substances and Explosive Atmospheres Regulations (DSEAR)

S.I. 2002/2776

Statutory framework requiring risk assessment, classification of hazardous zones, and prevention of ignition sources where explosive atmospheres may occur.

Key Statutory & Technical Requirements:
  • Hazardous area classification: Zones 0, 1, 2 (gases/vapours) and Zones 20, 21, 22 (combustible dusts).
  • Selection of certified ATEX/UKEX explosion-protected electrical equipment.
  • Control of static electricity, lightning protection, and bonding in hazardous areas.

Health and Safety at Work etc. Act 1974 (HASAWA)

1974 c. 37

Primary enabling Act establishing the general duties of employers to ensure, so far as is reasonably practicable, the health, safety, and welfare of employees and the public.

Key Statutory & Technical Requirements:
  • Section 2: General duty to provide safe systems of work and adequate training.
  • Section 7: Duty of employees to take reasonable care of themselves and others.
  • Section 16 and 17: Statutory approval and evidential status of Approved Codes of Practice (ACOPs).
TIER 2 // DESIGNATED INSTALLATION & MACHINERY STANDARDSCONSENSUS STANDARD

Engineering & Manufacturing Codes

Designated British and harmonised European standards providing presumed conformity with statutory health and safety objectives.

BS 7671:2018+A4:2026

IET Wiring Regulations 18th Edition

The national standard for electrical installation design, selection, erection, and verification in the UK (low voltage up to 1000V AC and 1500V DC).

Key Statutory & Technical Requirements:
  • Part 4: Protection for safety: ADS, electric shock, thermal effects, overcurrent, and voltage disturbances.
  • Part 5: Selection and erection of equipment: common rules, wiring systems, switchgear, earthing and bonding.
  • Part 6: Inspection, testing, and reporting (initial verification and periodic EICR).
  • Part 7: Special installations or locations (bathrooms, swimming pools, EV charging, solar PV, medical locations).

BS EN 60204-1:2018

Safety of Machinery: Electrical Equipment of Machines

Standard for electrical, electronic, and programmable equipment of industrial machinery. Governs panels, operator controls, and safety circuits.

Key Statutory & Technical Requirements:
  • Stop Category 0: Uncontrolled stop by immediate power disconnection.
  • Stop Category 1: Controlled stop with power maintained to decelerate, then isolated.
  • Stop Category 2: Controlled stop with power maintained to actuators.
  • Section 5.3: Supply disconnecting devices (lockable isolator).
  • Section 9.1: Control circuits supplied via PELV/SELV transformer at 24V DC.

BS EN 60204-32:2008

Machinery Safety: Hoisting & Cranes

Specific requirements for hoisting machines, overhead cranes, hoists, winches, and material handling systems.

Key Statutory & Technical Requirements:
  • Fail-safe electro-hydraulic thruster brakes and emergency lowering controls.
  • Slip ring rotor resistor interlocks and torque limiters.
  • Regenerative overspeed protection and limit switch arrangements.

BS EN 61439-1 / BS EN 61439-2

Low-Voltage Switchgear and Controlgear Assemblies

Design verification and assembly standard for industrial switchboards, motor control centres (MCCs), and distribution boards.

Key Statutory & Technical Requirements:
  • Design verification through 13 separate testing and assessment criteria.
  • Forms of Internal Separation: Form 1 through Form 4b dividing busbars, functional units, and terminals.
  • Short-circuit withstand strength (Icw / Icc) verification.

BS EN 61800-5-2:2017

Adjustable Speed Drives: Functional Safety

Specifies requirements for integrated safety functions inside modern variable speed inverters and servo drives.

Key Statutory & Technical Requirements:
  • Safe Torque Off (STO): Electronically disables gate pulses to IGBTs to prevent torque generation.
  • Safe Stop 1 (SS1) and Safe Stop 2 (SS2): Initiates and monitors deceleration ramps.
  • Safely-Limited Speed (SLS): Prevents motor exceeding specified speed limits.

BS EN 60034 Series (Parts 1 to 30-1)

Rotating Electrical Machines

Defines rating and performance, duty types, thermal insulation limits, and international efficiency classes for electric motors.

Key Statutory & Technical Requirements:
  • Duty cycles: S1 continuous duty through S10 discrete constant loads.
  • Thermal insulation classes: Class F (155 deg C) with Class B (80K) temperature rise margin.
  • Efficiency ratings: IE1 Standard, IE2 High, IE3 Premium, and IE4 Super Premium under eco-design regulations.
TIER 3 // LIFE SAFETY & HSE STATUTORY GUIDANCEACOP & STATUTORY GUIDANCE

Emergency, Detection & Testing Guidance

Codes of practice and Health and Safety Executive guidance establishing minimum benchmarks for emergency systems, fire alarms, and safe testing practices.

BS 5266-1:2016 / BS EN 50172

Emergency Lighting Code of Practice

Code of practice for the emergency escape lighting and standby lighting of domestic and non-domestic premises.

Key Statutory & Technical Requirements:
  • Escape routes: Minimum 1 lux along centre line.
  • Open areas (anti-panic): Minimum 0.5 lux across unobstructed floor space.
  • High-risk task areas: Minimum 10% of normal illuminance (not less than 15 lux).
  • Mandatory testing: Monthly functional flick tests and annual 3-hour rated duration discharge.

BS 5839-1:2017 / BS 5839-6:2019

Fire Detection & Alarm Systems

System design, installation, commissioning, and maintenance for non-domestic premises (Part 1) and domestic dwellings (Part 6).

Key Statutory & Technical Requirements:
  • Part 1 Categories: M (manual), L1 to L5 (life protection), P1 to P2 (property protection).
  • Part 6 Domestic Grades: Grade A (commercial panel) through Grade F (battery alarms), Categories LD1 to LD3.
  • Segregation of fire alarm cabling from general LV power circuits.

HSE Guidance Note GS38

Electrical Test Equipment for Use by Electricians

Health and Safety Executive specification for test leads, probes, and voltage indicators to prevent flashover and electric shock.

Key Statutory & Technical Requirements:
  • Probes must have finger barriers and maximum 4mm exposed metal tip (2mm or retractable sleeve preferred).
  • Test leads must be flexible, adequately insulated, and fused at 500mA where appropriate.
  • Voltage detectors must be proven on a known proving unit before and immediately after testing.

HSE Guidance HSG85

Electricity at Work: Safe Working Practices

Authoritative guidance on planning, managing, and carrying out work on or near electrical systems safely.

Key Statutory & Technical Requirements:
  • Clear decision tree enforcing dead working as the default standard.
  • Identification of equipment, secure point of isolation, and lock-out tag-out (LOTO) protocols.
  • Safety documentation: Permits-to-Work and Sanction-for-Test protocols for high-voltage or complex LV installations.
Sparks Switchboard
Quick: