DOL Motor Starter: 3D Switchgear, Slide-Rail Plinth & Inrush Workbench

How does an industrial starter enclosure convert operator pushbutton commands into physical 400V motor torque? Explore the real-time 3D mechanics of open-frame contactor armature pull-in, auxiliary seal-in hold-in (13-14), bimetal overload deflection, and BS EN 60204-1 Stop Priority and BS 7671 Reg 552.1.3 No-Volt Release across an interactive 3D switchgear enclosure, motor plinth, 2D IEC control schematic, and dynamic starting inrush oscilloscope.

Motors & Drives10 Min Interactive
• BS EN 60204-1 / BS EN 60947-4-1
C&G 2365 Unit 302

DOL Starter 3D Switchgear, Slide-Rail Plinth and Inrush Workbench

400V 3-Phase Feeder • 24V PELV / 110V AC Control Transformer (T1) • Slide-Rail Squirrel-Cage Motor
MECHANICAL: 0.0103x (15 RPM)ELECTRICAL: 50 Hz REAL TIME60 FPS● STANDBY
3D View Mode:
Inspect Gear:
Camera Angle:
Visibility:
ISOLATION & LOTO

Padlockable Supply Switch-Disconnector (Q1)

Manually operated main disconnecting switch isolating all active 3-phase supply lines. Must break stalled motor current (AC-23B duty) and allow up to three personal safety padlocks in the OFF position only.

Left-Drag: Orbit • Right-Drag: Pan • Scroll: Zoom • Tap Part: Inspect
12345678ABCDABCDPOWER CIRCUIT: 400V 3-PHASE 50HzCONTROL CIRCUIT (BS EN 60204-1 §9.4.3)L1 (Brown)L2 (Black)L3 (Grey)F0 (BS 88)Q1 ISOLATOR (LOTO)1352461/L13/L25/L32/T14/T26/T3KM1FR1U1V1W1M3 ~PE+24V DC (PELV §9.4.3)0V Return (Earthed at T1 Sec per §9.4.3)0FU1 (2A)1H3 Mains1112SB0 E-STOP2X1:3-431112SB1 STOP41314SB2 START1314KM1 (13-14)59596FR1 (95-96)6KM1A1A213-14 / 6B43-44 / 7B4344KM1 (43-44)7H2 Run9798FR1 (97-98)8H1 TripDOL STARTER SCHEMATIC (=DOL1)REV 02DWG: EEP-LAB-DOL-001 | SHT 1/1TRAINING SPECBS EN 60617 / BS EN 60204-1 / BS 7671UK EE PORTAL
DIN RAIL TERMINAL INTERFACE // GROUPS X1 & X2

Statutory Field Cabling & Control Loop Interface Schedule

IEC 60947-7-1 • BS EN 60204-1 §13.1 • EAWR 1989 Reg 5
TerminalGroupCircuit Function / DescriptionWire No.PotentialConductor / Statutory Reference
X1:1X1 ControlControl supply feed to remote Emergency Stop station124V DC / 110V ACDark Blue / Red • BS EN ISO 13850 (Series NC)
X1:2X1 ControlControl 0V common return rail (earthed at source)00V (PE Bonded)Dark Blue / Light Blue • BS EN 60204-1 §9.4.3
X1:3X1 ControlRemote Stop loop send (post E-Stop SB0)224V DC / 110V ACSeries NC Stop circuit (link to X1:4 if omitted)
X1:4X1 ControlRemote Stop loop return to local Stop button SB1:11324V DC / 110V ACBS EN 60204-1 §9.2.3.3 (Stop Priority)
X1:5X1 ControlRemote Start pushbutton feed out (from local Stop SB1:12)424V DC / 110V ACParallel NO Start circuit • BS EN 60204-1 §9.2.3.2
X1:6X1 ControlRemote Start return into seal-in node (joins SB2:14 / KM1:14)524V DC / 110V ACFeeds thermal overload relay trip contact FR1:95
X1:7X1 ControlRemote Motor Running telemetry output (switched by KM1 43-44)724V DC / 110V ACDedicated NO contact • BS EN 60204-1 §10.3.2
X1:8X1 ControlRemote Overload Trip alarm telemetry output (switched by FR1 97-98)824V DC / 110V ACNO contact • Illuminates amber warning indicator
X1:PEX1 EarthMain circuit protective bonding terminal / DIN rail CPCPE0V GroundGreen/Yellow • BS 7671 Reg 543 • Chassis bond
X2:1X2 ExceptedExcepted circuit anti-condensation heater Line (L)EX-L230V ACORANGE WIRE • Stays live when Q1 is OFF (§5.3.5)
X2:2X2 ExceptedExcepted circuit anti-condensation heater Neutral (N)EX-N0V ACORANGE WIRE • Requires warning decal at Q1 (§13.2.4)
X2:PEX2 EarthExcepted circuit protective earth conductor bondPE0V GroundGreen/Yellow • BS 7671 Reg 543.1
Contactor KM1:DE-ENERGISED (OPEN)
Aux Seal (13-14):OPEN
Overload (95-96):CLOSED (HEALTHY)
Motor Shaft:0 RPM (STOPPED)
Line Current:0.0 A
Mains Feed:400V HEALTHY
OPERATOR STATION // BS EN 60204-1 §10.122mm Industrial Actuators • IP65 Bezel
Standby (Ready to Start)
START (I)
STOP (O)
EMERGENCY STOP
RESET (FR1)
SUPPLY
RUN
TRIP
BENCH SIMULATION LEVERSTeaching & Network Fault Levers • Not Part of Starter
7.50 kW (14.15A FLC)
14.15 A (1.0x FLC) - Range: 12.0 to 18.0 A
7.20x FLC (IE3 Motor)
MOTOR START DYNAMICS

Starting Current & Shaft Speed vs Time • Locked-Rotor Inrush Decay

RMS Current (101.9A → 14.15A) Shaft Speed (0 → 1450 RPM) Rated FLC (14.15A)
Starting Current: 101.9 A (7.2x FLC)
Motor Shaft Speed: 0 RPM
Full Load Current: 14.15 A RMS
Run-Up Time: 1.80 s
Playhead: t = 0.00 s
BS EN 60947-4-1 // TYPE 2 COORDINATION

Log-Log Time-Current Characteristic (TCC) • Starting Locus vs Type C MCB vs BS 88-2 Fuse

Motor Starting Locus Type C 16A MCB (80-160A Band) BS 88-2 25M32 Fuse (Type 2) FR1 Overload Relay
Coordination Status: TYPE 2 REQUIRES CERTIFIED PAIRING
MCB Assessment: NUISANCE TRIP LIKELY (102A in 80 to 160A band)
Backup Protection: BS 88-2 MOTOR FUSE CLEARS SAFELY
Show Full Mathematical Derivation (AM2 & C&G 2365 Working Standard)
BS 7671:2018+A4:2026
Step-by-step engineering workingTransparent first-principles maths
Step 1: Rated Full-Load Current (FLC)

Motor Full-Load Current from Nameplate Shaft Power

FLC = P / (√3 × U × cosφ × η)
FLC = 7500 / (1.732 × 400 × 0.85 × 0.90) = 14.15 A
  • P: Shaft mechanical power = 7.50 kW (7500 W)
  • U: Line-to-line 3-phase supply voltage = 400 V RMS (BS 7671 §2.3.2)
  • cosφ: Rated motor power factor at full load = 0.85
  • η: Efficiency class rating = 0.90 (IE3 Premium Efficiency per SI 2021/745)
BS EN 60034-1 & C&G 2365 Unit 302
Step 2: Locked-Rotor Starting Inrush Current (I_LR)

Direct-On-Line Starting Inrush Multiplier

I_LR = k × FLC
I_LR = 7.20 × 14.15 A = 101.88 A RMS
  • k: Locked-rotor current ratio (I_LR / I_FLC) = 7.20x FLC (IE3 typically 6.0 to 8.5x FLC)
  • FLC: Continuous rated full-load current = 14.15 A
BS EN 60947-4-1 Table 2 & IEC 60034-12 Design N
Step 3: Peak Asymmetric Starting Current (I_peak)

First Half-Cycle Sub-Transient Peak (DC Offset Component)

I_peak = √2 × I_LR × [1 + exp(-π / (X/R))]
I_peak = 1.414 × 101.88 A × 1.527 = 220.08 A Peak
  • √2: RMS-to-peak sinusoidal crest factor = 1.414
  • X/R: Motor inductive reactance to resistance ratio at locked rotor ≈ 4.0
  • Asymmetry factor: 1 + exp(-π / 4.0) = 1.527 (DC component adds up to 108% to peak envelope)
BS EN 60947-4-1 Clause 9.3.3.5.2 & IEEE 141
Step 4: Feeder Cable Starting Voltage Drop (ΔV_start)

Voltage Drop During Locked-Rotor Inrush Interval

ΔV_start = (mV/A/m × I_LR × L) / 1000
ΔV_start = (11.0 × 101.88 A × 25 m) / 1000 = 28.02 V (7.01%)
  • mV/A/m: 4.0 mm² 70°C thermoplastic copper cable = 11.0 mV/A/m (BS 7671 Appendix 4 Table 4D1B)
  • L: Feeder route length = 25 m
  • Statutory note: Under BS 7671 Appendix 4 Section 6.4, the 5% continuous running limit does not apply during motor starting transients, provided the terminal voltage remains above contactor drop-out voltage (minimum 75% of Uc) and motor breakaway torque remains sufficient.
BS 7671:2018+A4:2026 Appendix 4 §6.4 & Table 4D1B
Step 5: Upstream Protection Coordination (Type C MCB vs BS 88-2)

Magnetic Instantaneous Trip Withstand Verification

Instantaneous Band: 5 to 10 × In (Type C) vs I_peak
16A Type C Band = 80 A to 160 A Peak • I_peak = 220.08 A → FAIL: NUISANCE TRIP HIGHLY PROBABLE
  • Verdict: Because peak sub-transient current (220.08 A) exceeds the 160 A instantaneous magnetic threshold of a 16A Type C MCB, cold starting is likely to trip the circuit breaker.
  • Tutor Recommendation: Upgrade upstream breaker to Type D MCB (10 to 20 × In) or install BS 88-2 dual-rated motor fuses (e.g. 25M32 / gM) to achieve certified Type 2 coordination under BS EN 60947-4-1 without nuisance tripping.
BS EN 60898-1 & BS EN 60947-4-1 §9.3.3.1
Formula & factors cross-checked against BS 7671:2018+A4:2026. Free of black-box approximations.

Control Circuit Principles: BS EN 60204-1 and BS EN 60947-4-1

1. BS EN 60204-1 Clause 9.2.3.3: Stop Overrides Start

Under UK and European machinery safety legislation, the Stop function must always take priority over the Start function. In this workbench, notice that the Normally Closed (NC) Stop pushbutton SB1 is wired physically in series ahead of both the Normally Open (NO) Start pushbutton SB2 and the contactor auxiliary hold-in contact 13-14. If an operator holds down the green Start button while simultaneously depressing the black Stop button (BS EN 60204-1 §10.2.1), the circuit path is severed unconditionally, instantly dropping the coil KM1 and opening the power contacts.

2. BS EN 60204-1 Clause 7.5: No-Volt Release (Under-Voltage Protection)

Why use momentary pushbuttons instead of a simple rotary toggle switch? If mains power fails while a motor is running with a toggle switch, the motor would instantly restart at full speed as soon as power is restored, posing extreme mechanical and human entrapment hazards. Depress the Mains Outage / Restore button in the fault panel above to see this safety principle in action:

3. Control Supply Earthing: 24V DC PELV vs 110V AC Earthed Control Transformer

Standard UK industrial control circuits avoid direct 230V AC or 400V mains operation for operator pushbuttons:

4. BS EN 60947-4-1 AC-3 vs AC-3e Utilization Categories

High-efficiency IE3 and IE4 motors draw higher locked-rotor currents (7.5 to 8.5 times rated full load current) than older legacy motors. Standard AC-3 ratings are verified only up to 6 to 7 times rated current. Always select contactors explicitly tested and certified to AC-3e to prevent contact bounce micro-welding during direct-on-line starting.

PRACTICAL WORKBENCH PROCEDURES

Electrical Inspection & Maintenance Bench Jobs

Step-by-step statutory test protocols and plant-room fault finding routines for industrial DOL starter panels.

Safe Isolation Protocol (BS EN 60204-1 §5.3 / EAWR 1989 Reg 12 & Reg 13)

Before opening the enclosure door or touching any terminal screw, strict safe isolation must be proven dead using a dedicated voltage indicator and proving unit conforming to HSE Guidance Note GS38.

Step 1: Identify supply switch-disconnector Q1 and obtain plant permit to work.
Step 2: Rotate Q1 handle to OFF (0). Fit safety lockout hasp, padlocks, and warning tag to prevent re-energisation. Keep the key in your custody.
Step 3: Test GS38 two-pole voltage indicator on proving unit to confirm operational status.
Step 4: Prove dead on all incoming lines: L1-L2, L2-L3, L1-L3, L1-PE, L2-PE, L3-PE, and 24V control circuit rails.
Step 5: Re-test voltage indicator on proving unit to verify probe integrity.

Statutory Legal Duty

Electricity at Work Regulations 1989 Regulation 12 mandates adequate means for cutting off electricity, while Regulation 13 mandates that adequate precautions shall be taken to prevent electrical equipment that has been made dead from becoming electrically charged while work is carried out (locking off and testing with a GS38 voltage detector). Failure to isolate and lock off is a criminal offence under UK statutory law.

Direct-On-Line Motor Starter Apparatus Schedule

Switchgear Apparatus Specifications and Terminal Designations
DesignationComponent DescriptionStandardTerminal Markings
Q13-Pole Switch-Disconnector with Door Interlock HandleBS EN 60947-3Line: 1/L1, 3/L2, 5/L3 • Load: 2/T1, 4/T2, 6/T3
F0BS 88-2 Motor Backup Fuses (25M32 gM Motor Rated)BS 88-2 / IEC 60269-280kA breaking capacity • Type 2 Coordination
KM13-Pole Block Contactor with 24V PELV CoilBS EN 60947-4-1 (AC-3e)Main: 1-2, 3-4, 5-6 • Coil: A1-A2 • Aux Seal: 13-14 • Aux Run: 43-44
FR1Thermal Bimetallic Overload Relay (Class 10 Trip)BS EN 60947-4-1Power: 2/T1, 4/T2, 6/T3 • NC Contact: 95-96 • NO Alarm Contact: 97-98
M17.5 kW 4-Pole 3-Phase Squirrel-Cage Induction MotorBS EN 60034-1 (IE3)400V Delta • 14.15A FLC • 1450 RPM • Terminals: U1, V1, W1, PE
TECHNICAL ASSESSMENT

DOL Starter Apprentice CPD Verification Quiz (12 Questions)

Validate your understanding against British and International electrotechnical standards.

Question 1 of 12• Score 0 / 12
BS EN 60204-1 Clause 9.2.3.3 / C&G 2365 Unit 302

Scenario: An operator holds down the green Start pushbutton (SB2) while an emergency stop (SB0) or black Stop pushbutton (SB1) is depressed simultaneously.

Under BS EN 60204-1 Clause 9.2.3.3, what must occur within the starter control circuit?

Sparks Switchboard
Quick: