Inside an SMPS: Switch-Mode Power Supply & Electronic Fuse Physics

Why do standard thermal-magnetic circuit breakers fail to trip when a 24V DC field sensor short-circuits, crashing the entire machine automation panel? Explore the internal silicon physics of an industrial Switch-Mode Power Supply (SMPS) and Electronic Circuit Breaker (ECB): primary 325V DC link rectification, 100 kHz MOSFET PWM flyback chopping, PELV vs SELV earthing, and how active electronic circuit breakers clamp peak fault current in ≤10μs and selectively disconnect shorted branches within 10ms to keep PLCs online under BS EN 60204-1 and BS EN 61131-2.

Switchgear & Protection⏱️ 8 Min Interactive
• BS EN 61204-7:2018
🔌

24V DC SMPS & 4-Channel ECB Interactive 3D lab

230V AC Input • 100 kHz Flyback Chopper • 24V PELV Bus • Selective Electronic Protection
60 FPS● 24.0V DC REGULATED (NORMAL)
3D View Mode:
Inspect Part:
Camera Angle:
Visibility:
ENERGY STORAGE & REINFORCED ISOLATION

High-Frequency Split-Bobbin Flyback Transformer

Gapped high-frequency coupled inductor operating at 100 kHz. Stores magnetic energy in its center-limb air gap during MOSFET conduction, and discharges into the secondary winding during off-time. Provides reinforced dielectric isolation between hazardous 230V AC mains and safe 24V DC PELV circuits per BS EN 62368-1.

Left-Drag: Orbit • Scroll: Zoom • Tap Part: Inspect
DIN RAIL TERMINAL INTERFACE // GROUPS X1 & X2

Statutory Mains & 24V DC Distribution Interface Schedule

BS EN 60204-1 §6.4 • BS EN 61131-2 • EAWR 1989 Reg 5
TerminalGroupCircuit Function / DescriptionWire No.PotentialConductor / Statutory Reference
X1:LX1Incoming 230V AC Single-Phase Line Feed1230V AC 50HzBS 7671 §411 (Automatic Disconnection)
X1:NX1Incoming 230V AC Neutral Reference20V (Neutral)BS 7671 §411 / EAWR 1989 Reg 9
X1:PEX1Main Enclosure Protective Earth BondPE0V (Earth Potential)BS 7671 §543 / EAWR 1989 Reg 8
X2:1X2Protected Channel 1: Safety PLC & Relays2224V DC (PELV)BS EN 61131-2 §5.1.1
X2:2X2Protected Channel 2: Industrial HMI Screen & IPC2324V DC (PELV)BS EN 61131-2 §5.1.1
X2:3X2Protected Channel 3: Machine Field Sensors & Switches2424V DC (PELV)BS EN 60204-1 §9.4.3.1
X2:4X2Protected Channel 4: Solenoid Valves & Actuators2524V DC (PELV)BS EN 60204-1 §9.4.3
X2:0VX2PELV 0V Common Reference (Bonded to PE)210V (PELV Grounded)BS EN 60204-1 §9.4.3.1 / BS 7671 §414
X2:13X2DC OK Relay Contact Common3024V DC SignalBS EN 60204-1 §13.2.4
Output DC Voltage24.0 VNominal Regulated Rail
Total Bus Current8.5 A42.5% of 20A Capacity
Switching Frequency100 kHzPrimary MOSFET Chopper
Earthing ModePELV0V Bonded to PE Bar
Protection ModeECBActive Solid-State Breaker
Channel 3 StateNORMALSensor Bus Online
OPERATOR CONTROLS

Panel Switching & ECB Station

BS EN 60204-1 §9.2
Mains Isolator (Q1)
ECB Channels
Master Reset
COMMISSIONING LEVERS

Electrical Tuning & Protection

BS EN 61131-2
Protection Technology:
PRIMARY SWITCHING SCOPE

100 kHz MOSFET PWM & Clamp Envelope

Time Domain: 2 μs/div
V_ds (Drain Voltage) I_d (Primary Current)
Duty Cycle: 38.5%Peak V_ds: 540 VRCD Clamp: HEALTHY
PROTECTION TRIP SCOPE

24V Bus Transient & Selectivity Trip

Time Domain: 5 ms/div
24V Bus Voltage Ch 3 Fault Current
Response: ≤10 μs Active ClampDisconnection: 10 ms SelectivePLC Health: ONLINE (>20.4V)
GLASS-BOX DERIVATION PAD

First-Principles Mathematical Derivation

Pure Functions in calculations.ts • BS 7671 • BS EN 61131-2
RefParameterFormulaSubstitutionResult
CALC-01Primary Rectified DC LinkV_bulk = V_ac × √2 - 2 × V_f230 × 1.4142 - 1.40323.87 V DC
CALC-02Flyback Peak Primary CurrentI_pk = (V_bulk × D) / (L_p × f_sw)(323.87 × 0.385) / (0.00035 × 100000)3.56 A Peak
CALC-03Stored Magnetic Energy per CycleE = 0.5 × L_p × I_pk²0.5 × 0.00035 × (3.56)²2.22 mJ (222 W)
CALC-04Type C MCB Magnetic FloorI_mag = 10 × I_n10 × 6.0 A60.0 A Required
CALC-05SMPS Current Foldback LimitI_lim = 1.15 × I_rated1.15 × 20.0 A23.0 A Max Supply
CALC-06MCB Magnetic Deficit (Paradox)ΔI = I_mag - I_lim60.0 A - 23.0 A37.0 A Deficit (NO TRIP)
CALC-07ECB Active Clamping CeilingI_clamp = 1.25 × I_channel1.25 × 2.0 A2.50 A (≤10 μs)
CALC-08Capacitor Bleeder Discharge Timet = -τ × ln(V_safe / V_initial)-70.5 × ln(60 / 325)119.11 s to Safe ES1
PRACTICAL WORKBENCH PROCEDURES

SMPS & Electronic Protection Bench Jobs

Step-by-step statutory test protocols and workshop fault finding routines for industrial DC automation systems.

Safe Isolation & Residual Stored Energy Protocol

Switch-mode power supplies store lethal energy in primary electrolytic capacitors long after the mains isolator is opened. Follow this statutory procedure under EAWR 1989 Regulations 12, 13, and 14.

Step 1: Rotate panel switch-disconnector Q1 to OFF (0). Fit personal safety padlock and danger tag. Keep the key in your personal custody.
Step 2: Test your GS38 two-pole voltage detector against an independent proving unit to confirm operation.
Step 3: Probe incoming mains terminals X1:L to X1:N, X1:L to X1:PE, and X1:N to X1:PE. Confirm zero voltage.
Step 4: Re-test your two-pole voltage detector against the proving unit (Prove-Test-Prove).
Step 5: Probe primary DC bulk capacitor terminals. Verify voltage decays below 60V DC (ES1 safe threshold) before touching circuit board components. Allow at least 120 seconds for internal bleeder dissipation.

Statutory Safety Note (HSE GS38 & EAWR 1989)

Under HSE GS38, digital multimeters are strictly prohibited from proving dead due to incorrect rotary switch selections, blown internal fuses, and un-fused leads. Use an approved two-pole voltage indicator with shrouded probes and test against a known source before and after isolation.

TECHNICAL ASSESSMENT

SMPS & Electronic Protection Technical Assessment (12 Questions)

12 Scenario-Based Plant-Room Questions • BS EN 60204-1, BS EN 61131-2, and HSE GS38

Question 1 of 12• Score 0 / 12
BS EN 60898-1 / BS EN 60204-1 §9.4.3

Scenario: An electrical improver installs a 6A Type C miniature circuit breaker to protect a 24V DC branch feeding field proximity sensors from a 20A industrial switch-mode power supply. A cable develops a dead short circuit to frame.

Why does the 6A Type C circuit breaker fail to trip magnetically, causing a total automation panel blackout?

5-Pillar UK Statutory & Standards Compliance Framework

01. MACHINERY SAFETY

BS EN 60204-1 §6.4 & §9.4.3.1 (PELV Earthing)

Mandates that 24V DC machinery control circuits must be arranged as Protective Extra-Low Voltage (PELV) with the 0V reference bonded to the protective bonding circuit (PE). Under Clause 9.4.3.1, this ensures that any insulation breakdown between +24V and the machine frame creates an immediate dead short that disconnects the branch protective device instantly, preventing unintended spontaneous machine restarting.

02. AUTOMATION ENVELOPE

BS EN 61131-2 §5.1.1 (PLC Voltage Limits)

Specifies the mandatory operating voltage envelope for programmable controllers: 20.4V to 28.8V DC (-15% to +20%). When an un-cleared branch short pulls the 24V bus below 19.2V for longer than 10 milliseconds, internal power supplies drop out, dumping output tables and triggering emergency stops across the entire plant.

03. ELECTRICAL INSTALLATIONS

BS 7671:2018+A3:2024 Section 414 (SELV vs PELV)

Regulates extra-low voltage systems. Regulation 414.4 permits PELV circuits and exposed metal parts to be earthed, whereas SELV circuits must remain floating and isolated from earth. For machinery control panels, floating SELV without continuous insulation monitoring is prohibited due to undetected double-fault hazards.

04. APPARATUS SAFETY

BS EN 62368-1 Clause 5.4 (Reinforced Isolation)

Classifies primary mains circuits as Energy Class 3 (ES3, lethal hazard) and secondary 24V circuits as Energy Class 1 (ES1, touch-safe). Mandates reinforced insulation barriers featuring minimum 6.4mm creepage distance and 4.0mm clearance through air, verified by physical milled slots in the PCB substrate.

05. STATUTORY DUTY

Electricity at Work Regulations 1989 & HSE GS38

Regulation 11 requires efficient means for protecting systems from excess current. Regulation 14 prohibits live diagnostic probing unless strictly justified under the tripartite test. HSE GS38 mandates approved two-pole voltage indicators with shrouded probes for proving dead.

Sparks Switchboard
Quick: